program transponder key ford without original
Blog

Ford Intelligent/Transponder Access Key Programming

Ford has been a famous car manufacturer for decades. They offer a variety of cars with different engine sizes and options to meet any driver’s needs in the market. One thing that many drivers don’t know about Ford is how simple it can be to program their transponder key without original keys. While doing so, You can save money and time by using a program transponder key ford without an original.
In this blog post, we will talk about what you need to do so and which steps are necessary for programming your new key.

Keeping the first things first, A transponder key is a secure device that uses radio waves to send unique alphanumeric codes to your car’s ignition system. Your car won’t start without the code programmed in, so if you can’t find any of your original keys, don’t worry- we’ll walk you through how to program a new key without needing an original one.

transponder key programming

Material Required:

Things you will need are listed below to do so-

  • Ford transponder key
  • Phillips head screwdriver
  • Wire cutters

These are all needed for programming your new key.

how to program a transponder key without original

Steps to program a Ford Transponder Key without original keys:

Follow the instructions given below to how to program transponder key ford without original:

To start with, you will take off the back cover of the battery compartment by unscrewing the cap. Then you will take out the wires that are connected to it. You’ll put these back later, but first, we need to program your new key.

Next, remove any of the keys from the ignition and then use a Phillips head screwdriver to twist off each one for them not to be accidentally turned on.

Now, take your wire cutters and remove the cover to expose the metal around each keyhole. Take note of which slot you want to use for programming and all other ones that will not be used again.

Remove any keys from the ignition and twist off with a Phillips head screwdriver; then remove the exposed metal from the opening using wire cutters.

Now you want to take your new key and snap it off in a way that will allow for easy attachment; later on, this can be done by snapping its head right below the top of the door or where ever is comfortable for you without removing it it any more than necessary.

You’ll want to insert it into the slot you want to use for programming.
Now, twist your new key to place metal of its edge around each tooth like before and then pull outwards towards you with some force until it clicks; this will ensure that a good connection has been made on all teeth.

After checking over your project one last time, you’ll want to replace the back cover and screw it tightly in place.

Now turn your key over about an inch or two while holding it firmly between your fingers at the end of its head that is still exposed, then push down with all of your might on top of the metal area where the teeth are located until they pop out one at a time.

This will make the teeth pop out one at a time, and you’ll want to remove them with your fingers carefully.

The next step is removing any of the old key shafts that are still sticking up; this can be achieved by pressing down on the base end of each tooth while pulling it straight up until it pops out.

Then you’ll need to insert the new key’s shafts into their proper place, which is demonstrated by using your fingers to push them in until they click and stay seated securely.

Once that’s done, you can carefully remove any remaining pieces of metal from the old key with pliers or a screwdriver before inserting the new key and turning it in the ignition.

Once you’re able to turn your car’s engine on, make sure all of the lights work correctly before driving off to be safe!

ford pats key programmer

FAQs

Q1. How do I know whether my car key has a transponder?

If your car’s key enters the ignition system when you are not driving and does not set off a theft alarm, then that key is probably a transponder. Transponder keys usually have chips inside their heads.

You can also tell by using the hit and the trial method. This is done by starting your car engine with a non-responder key. If your car turns on, then that means it has a responder system; it won’t turn on otherwise. Be careful while doing this because if your vehicle has a responder system, then you’ll.

Q2. Do you want to program your transponder key?

You don’t need a professional transponder key programmer to help you program your transponder. You can do this by yourself, as long as you follow the correct procedure. The programming process isn’t complicated, but it also depends on the type of car. Programming from your vehicle allows for faster and easier work, which usually takes about forty-five minutes.

Q3. Do you need an original transponder key if I have only one?

Yes, you can program a KeylessOption transponder key with having just one working key. You will need to have unique keys like the KeylessOption transponder key to use just one pass for programming. It’s simple and easy to do, but remember that it needs to be from the right when programming new keys on your vehicle.

Q4. Do you want to bypass the car’s keyless entry system?

Of course, the easiest way to bypass a programmable key is to perform a permanent re-wiring of your car’s ignition. The kit that you need will vary depending on older cars; if you have an older car with no programming, there’s nothing special required for it.

You can also insert another transponder key designed for your vehicle’s make into the car’s ignition, turn it on for about ten to eleven minutes. Repeat this step more than three times to bypass your original key with a new door key, then remove the new transponder from the ignition without turning your vehicle on.

Share Button